Skip to main content
Truong Thinh Corp - Steel Structure Manufacturer

Corrosion Under Insulation: Hidden Risks for Steel Structures

- Truong Thinh Corp

Corrosion under insulation is rust that forms on steel hidden beneath insulation, lagging or cladding. Because the steel cannot be seen, the damage often grows for years before it is found. It affects pipes and vessels in plants and also structural steel in cold stores, food plants and wet environments, wherever insulation or panels cover the steel.

How corrosion under insulation starts

Water gets in through gaps, damaged cladding, poor seals or condensation. The insulation holds the moisture against the steel, and the steel stays wet for long periods. Corrosion needs water and oxygen, as explained in this overview of corrosion, and the insulation keeps both in contact with the steel.

Where it is most likely

  • Steel in cold stores and chilled areas, where condensation is common
  • Steel inside wet processing areas that are washed down
  • Steel behind panels that have damaged joints or seals
  • Steel at penetrations, supports and fixings through insulation
  • Steel in humid or coastal sites with poor ventilation

Our guides to steel structures for cold storage and to steel structures in tropical climates describe environments where the risk is higher.

Corrosion under insulation is prevented by good coating: hot-dip galvanized steel members stored in a factory
Hot-dip galvanized steel members stored in a factory

Preventing corrosion under insulation

  1. Coat the steel properly before the insulation goes on. A good system, with surface preparation to the specified grade, is the main defence. See Sa 2.5 blast cleaning.
  2. Choose a suitable coating, such as galvanizing or a duplex system. See galvanized vs painted steel.
  3. Seal the envelope, so water cannot enter at joints and penetrations.
  4. Control condensation, with a continuous vapor barrier on the warm side. Our guide to roof cladding, insulation and fixings covers this.
  5. Provide drainage, so that any water that enters can leave.
  6. Avoid details that trap water, such as upward-facing pockets.

Inspection

Inspection is hard because the steel is hidden. Visual checks of the cladding, seals and fixings show where water may enter. Where damage is suspected, remove a small section of insulation to inspect the steel, or use methods designed for inspecting hidden steel. Plan inspection points in the design, so that access exists later. Our guide to maintaining steel structures lists the routine checks.

Repair

If corrosion is found, remove the insulation in the area, clean the steel back to sound metal, recoat it with a compatible system and reseal the envelope. Fix the source of water, or the problem returns. Our guide to touch-up painting steel after erection explains how to repair coatings.

Why early detection matters

Corrosion under insulation rarely shows until it is advanced. A small leak can run for years and thin the steel from the inside out. Finding it early lets a local repair replace a major replacement, and it protects the load path of the building. Keep a record of inspections, photographs and any repairs, so that trends become visible and the next inspector knows where to look.

Design for an industrial steel building

When you plan an industrial steel building with insulated panels or lined walls, ask the designer how the details handle moisture, who inspects the envelope and how repairs will be made. A building that is easy to inspect is easier to keep sound.

If you need a coating and detailing review for a steel structure with insulation, contact the engineering team and send the drawings.

Frequently Asked Questions

Is corrosion under insulation only a problem in pipes?

No. It also affects structural steel behind insulation or panels, especially in cold or wet environments.

How can I tell if it is happening?

Look for stains, damaged cladding, wet insulation and bulging seams. Remove a sample area to see the steel.

Does galvanizing prevent it?

It reduces the risk, but does not remove it if the steel stays wet for long. Sealing and condensation control are also needed.

Free quotation · Reply within 24 working hours

Request a quotation for corrosion under insulation

Tell us about your steel structure project. Our engineering and sales team will reply with a tailored proposal, usually within 24 working hours.

Need an answer faster? Call our engineers directly.

Mon–Fri 8:00–17:30 · Sat 8:00–12:00 (GMT+7)

Call now: +84 935 657 568
No drawings yet? Choose "No drawings yet" and send the request anyway. Our engineers will advise first.
PDF, DWG, DXF, ZIP, Excel, Word or images. Up to 5 files, 15 MB each.

Truong Thinh Corp - Author at Truong Thinh Corp
Truong Thinh Corp

Truong Thinh Corp – Steel Structure Services

We design, manufacture, supply and erect pre-engineered steel structures for factories, warehouses and industrial projects across Southeast Asia.

Request a Free Quotation