Skip to main content
Truong Thinh Corp - Steel Structure Manufacturer

S355 Steel Grade Explained for Buyers: Properties and Use

- Truong Thinh Corp

S355 steel is one of the most used grades in European-style structural steel. The number refers to the minimum yield strength in megapascals for thinner sections. It is stronger than S235 and S275, so members can be lighter for the same load. Buyers should know what the name means, where the grade is used and why it should never be swapped for a similar grade without approval.

What the name means

In the European system, S stands for structural steel and the number gives the minimum yield strength in MPa for the thinnest thickness range. Letters after the number describe the toughness test, for example JR, J0 or J2. Yield strength falls slightly as thickness increases, so the value in the standard depends on thickness. The standard lists the exact numbers. A general overview of common structural steel grades gives context.

How S355 compares with S235 and S275

| Grade | Typical minimum yield for thin sections | Typical use | |—|—|—| | S235 | 235 MPa | General plates and light members | | S275 | 275 MPa | Secondary members and many building frames | | S355 | 355 MPa | Main frames, heavily loaded members, long spans |

The values are general references. The project specification and the standard decide the numbers for each thickness. Our technical specifications page lists the grades and standards we commonly work with.

S355 steel identification in the yard: a steel grade identification board beside stacked structural steel
Steel grade identification board beside stacked structural steel

Why choose S355 steel

  • Lighter members. Higher strength allows smaller sections for strength-governed designs.
  • Lower tonnage in some frames, which can reduce fabrication and transport.
  • Long spans and heavy loads, where member weight matters.

It does not help where stiffness or deflection governs, since stiffness depends on the modulus, which is the same for all structural steel grades. See steel beam deflection.

What to watch when using S355 steel

  • Welding. Higher grades may need controlled procedures, such as preheat, depending on thickness and joint. Follow the qualified procedure. See welding procedure specifications.
  • Toughness. Choose the right toughness designation for the temperature and loading.
  • Availability. Check that plate or sections in the required thickness are available, since lead time depends on it.
  • Documents. Ask for mill certificates that show the grade, the heat number and the test results. See mill test certificates.

Grades are not interchangeable

Do not assume that a grade from one standard is equal to a grade in another, even if the strength looks similar. Differences in chemistry, toughness and testing can matter. If an alternative is proposed, the engineer must approve it in writing, and the certificates must show that it meets the specification. Our guide to design codes for steel structures in Vietnam explains how to state the governing standards.

Coating and fabrication

Grade does not change corrosion resistance in practice, so the coating system is chosen by exposure, as covered in galvanized vs painted steel. Cutting, drilling and bending of higher grades should follow the fabricator's procedures.

What to put in the specification

State the grade, the standard, the toughness class, the thickness ranges and the documents required. Ask the supplier to confirm each in the quotation. When you compare each steel structure supplier, check that the grades listed match your specification, as in compare steel structure quotations.

If you need to confirm the grade for a package, contact the engineering team and send the specification.

Frequently Asked Questions

Is S355 always better than S275?

Not always. It is stronger, but cost, availability, welding needs and stiffness limits all matter. The engineer chooses.

Does S355 steel rust less?

No. Corrosion resistance is similar for these grades. The coating system protects the steel.

Can another grade replace S355 on site?

Only with written approval from the engineer and matching certificates.

Free quotation · Reply within 24 working hours

Request a quotation for s355 steel

Tell us about your steel structure project. Our engineering and sales team will reply with a tailored proposal, usually within 24 working hours.

Need an answer faster? Call our engineers directly.

Mon–Fri 8:00–17:30 · Sat 8:00–12:00 (GMT+7)

Call now: +84 935 657 568
No drawings yet? Choose "No drawings yet" and send the request anyway. Our engineers will advise first.
PDF, DWG, DXF, ZIP, Excel, Word or images. Up to 5 files, 15 MB each.

Truong Thinh Corp - Author at Truong Thinh Corp
Truong Thinh Corp

Truong Thinh Corp – Steel Structure Services

We design, manufacture, supply and erect pre-engineered steel structures for factories, warehouses and industrial projects across Southeast Asia.

Request a Free Quotation