Skip to main content
Truong Thinh Corp - Steel Structure Manufacturer

Hollow Steel Sections vs Open Sections: CHS, RHS and H-Beams

- Truong Thinh Corp

Hollow steel sections are tubes: round (CHS), square or rectangular (RHS and SHS). Open sections, such as I-beams, H-beams, channels and angles, have a shape with open sides. Each type has strengths, so structures often use both. The right choice depends on the load, the connections, the appearance and the cost.

What hollow steel sections are

A hollow section is a closed tube, made by rolling and welding strip or by forming from a billet. The closed shape resists twisting and buckling in several directions. The family is described in this overview of hollow structural sections. Open sections are rolled or fabricated with a web and flanges, and are efficient in bending about one axis.

Where hollow steel sections work well

  • Trusses and space frames, where members carry axial force and a closed shape resists buckling. See steel roof truss types.
  • Columns, especially where load comes from several directions or where appearance matters.
  • Handrails, frames and canopy structures, where a clean look is useful.
  • Members exposed to wind, since a round section can have lower wind drag.
Hollow steel sections in trusses: lattice roof trusses against a blue sky with scattered clouds
Lattice roof trusses against a blue sky

Where open sections work well

  • Beams and rafters, where bending dominates and the I-shape is efficient. See built-up H-beam vs hot-rolled.
  • Columns in portal frames, which connect easily to beams and bracing.
  • Members that need simple bolted connections, since flanges give a flat surface.

Connections and fabrication

Hollow sections are often welded, with cut ends shaped to fit the member they join. The cuts for round tubes are curved, so cutting and fit-up need skill or a machine. Open sections are easier to bolt with plates. Our guide to bolted or welded connections explains how the choice affects the details.

Inside a closed tube, the surface cannot be reached for repainting, so the section must be sealed against water, or protected inside. Our guide to galvanized vs painted steel explains how coating decisions change for closed shapes. Vent and drain holes are needed for galvanizing hollow sections, so tell the fabricator early.

Comparing the two

| Point | Hollow sections | Open sections | |—|—|—| | Torsion | Strong | Weak | | Buckling in all directions | Good | Depends on axis | | Bolted connections | Harder | Easier | | Coating | Needs sealing or venting | Easier to coat | | Appearance | Clean | Utilitarian | | Cost per ton | Often higher | Often lower |

Cutting and preparing hollow steel sections

Hollow steel sections are cut square, mitred or profiled to fit against other tubes. Profile cuts need a machine or a template, and the fit-up gap is limited by the welding procedure. Good preparation reduces weld size and distortion, and it makes inspection easier. Ask the fabricator how end preparation is done and checked before welding.

How to decide

  1. Identify the main load in each member: bending, axial or torsion
  2. Check how the member will connect to the rest of the frame
  3. Consider appearance and coating needs
  4. Compare the total installed cost
  5. Confirm with the engineer

What to ask a supplier

Ask which hollow steel sections the supplier fabricates, how end cuts are made, how joints are inspected and how members are protected. Our page on steel structure components lists the parts we fabricate. When procurement is for a roof or mezzanine, see our guide to steel truss fabrication and our article on fabricating trusses for transport.

If you are choosing sections for a frame or truss, share the loads, the spans and the appearance needs, and discuss your structural design requirements with our engineering team.

Frequently Asked Questions

Are hollow sections stronger than open sections?

Not in general. They are strong in torsion and buckling in all directions, while open sections are efficient in bending. The load decides.

Can hollow sections be galvanized?

Yes, but they need vent and drain holes so that zinc can flow and air can escape. Plan these in the detailing.

Why are hollow sections more expensive?

They are often more costly per ton to manufacture, and welded connections take more fabrication time. The total cost depends on the design.

Free quotation · Reply within 24 working hours

Request a quotation for hollow steel sections

Tell us about your steel structure project. Our engineering and sales team will reply with a tailored proposal, usually within 24 working hours.

Need an answer faster? Call our engineers directly.

Mon–Fri 8:00–17:30 · Sat 8:00–12:00 (GMT+7)

Call now: +84 935 657 568
No drawings yet? Choose "No drawings yet" and send the request anyway. Our engineers will advise first.
PDF, DWG, DXF, ZIP, Excel, Word or images. Up to 5 files, 15 MB each.

Truong Thinh Corp - Author at Truong Thinh Corp
Truong Thinh Corp

Truong Thinh Corp – Steel Structure Services

We design, manufacture, supply and erect pre-engineered steel structures for factories, warehouses and industrial projects across Southeast Asia.

Request a Free Quotation