Skip to main content
Truong Thinh Corp - Steel Structure Manufacturer

High-Strength Bolts vs Ordinary Bolts in Structural Steel

- Truong Thinh Corp

High-strength bolts are made from heat-treated steel and carry far more load than ordinary bolts of the same size. They are used in the main structural connections of buildings and bridges. Ordinary bolts, with a lower grade, are used for light or secondary connections. The two must not be mixed up on site.

What makes high-strength bolts different

A bolt's grade describes its strength. High-strength grades have a higher tensile strength, and they come with matching nuts and washers. A general introduction is given in this note on the bolt. The grade is marked on the head, so it can be checked on site.

Where each is used

  • High-strength bolts. Main frame connections, splices, bracing and any joint that carries large forces or must be pretensioned.
  • Ordinary bolts. Secondary members, light brackets and connections where loads are low.

The engineer chooses the grade for each joint and shows it on the drawings. A change of grade needs approval.

High-strength bolts are tightened on site: steel frames and cranes on a building site during erection
Steel frames and cranes on a building site during erection

Tightening is part of the specification

High-strength bolts can be tightened to a specified tension so the plates grip each other. Our guide to bolt tightening methods for structural steel explains snug-tight, turn-of-nut, calibrated wrench and tension control methods. Ordinary bolts are tightened by hand wrench and not usually pretensioned.

Matching nuts and washers

Each high-strength bolt needs the nut and the washer that go with it. Mixing parts from different grades or standards can reduce the strength of the joint. Keep bolt assemblies together in their original packaging until use, and store them dry.

Storage and handling

Store bolts in their original containers, in a dry place, off the ground. Do not clean the lubricant from bolts that are supplied lubricated, because it controls the tightening result. Take out only the amount needed for the day, and return unused bolts to the container. Lots should not be mixed, and rusty or damaged bolts should be set aside. These small habits protect the quality of the joint far more than they appear to.

Common mistakes

  1. Using an ordinary bolt where a high-strength one is specified
  2. Mixing bolt lots or standards on one joint
  3. Reusing pretensioned bolts
  4. Dirty or oiled surfaces in friction joints
  5. Missing washers or wrong washer type

Documents and traceability

Bolts come with certificates for the grade and the lot. Keep them in the project file, and check that the marking on the bolts matches the certificate. Our guide to mill test certificates shows how traceability works for steel, and the same ideas apply to fasteners.

Quantities and packing

Order bolts with a small allowance for losses, and pack them by connection so that the crew finds the right ones. Our guide to steel member marking and packing lists explains how small items are labeled.

What to ask a supplier

When you compare each steel structure supplier, ask which standard the bolts follow, who supplies them, how they are certified and how they are packed. Our guide to compare steel structure quotations lists connection hardware as one of the eight items to check.

If you need to confirm bolt grades and quantities for a package, contact the engineering team and send the connection schedule.

Frequently Asked Questions

Can I replace a high-strength bolt with an ordinary bolt?

No, not without the engineer’s approval. It can reduce the capacity of the joint.

Are high-strength bolts always pretensioned?

No. Some joints use them snug-tight. The drawings state which joints need pretension.

How do I know the bolt grade on site?

Check the marking on the head and the certificate for the lot. They should agree with the specification.

Free quotation · Reply within 24 working hours

Request a quotation for high-strength bolts

Tell us about your steel structure project. Our engineering and sales team will reply with a tailored proposal, usually within 24 working hours.

Need an answer faster? Call our engineers directly.

Mon–Fri 8:00–17:30 · Sat 8:00–12:00 (GMT+7)

Call now: +84 935 657 568
No drawings yet? Choose "No drawings yet" and send the request anyway. Our engineers will advise first.
PDF, DWG, DXF, ZIP, Excel, Word or images. Up to 5 files, 15 MB each.

Truong Thinh Corp - Author at Truong Thinh Corp
Truong Thinh Corp

Truong Thinh Corp – Steel Structure Services

We design, manufacture, supply and erect pre-engineered steel structures for factories, warehouses and industrial projects across Southeast Asia.

Request a Free Quotation